You can buy used process equipment in the UK from specialist process plant dealers, auctions of factory and plant assets, manufacturers selling reconditioned machines and online marketplaces. The Commercial Trader, a UK marketplace for commercial vehicles, machinery and equipment, had about 635 listings of new and used industrial pumps for sale, about 465 processing vessels and about 150 mixers on 19 November 2026.
Process equipment is bought to do a specific job, so the specification matters more than the price. Know the duty you need a pump, mixer or vessel to do before you start comparing machines.
Where can you buy used process equipment in the UK?
Used process equipment is sold in five ways in the UK: by specialist process plant dealers, at auctions of factory and plant assets, by manufacturers, on online marketplaces and directly by plants that are closing or upgrading. The table shows what each route gives you and what to watch for.
| Route | What you get | What to watch for |
|---|---|---|
| Specialist process plant dealer | Vessels, mixers, pumps and reactors that have been inspected, sometimes tested or refurbished | Higher prices than auction, and stock limited to what the dealer holds |
| Auction of factory or plant assets | A whole plant’s equipment on one sale date | Sold as seen, a buyer’s premium on top, and removal at your cost |
| Manufacturer | Reconditioned equipment with the maker’s parts and support | A limited choice, in one make |
| Online marketplace such as The Commercial Trader | Listings from many sellers in one place, and direct contact with each seller | You arrange the inspection, the dismantling and the transport |
| Direct from a plant that’s closing or upgrading | Equipment you can see installed, with its history | No warranty, and removal to arrange |
What process equipment is listed on The Commercial Trader?
The Commercial Trader lists process equipment in eight categories of its industrial section, with about 1,900 listings between them on 19 November 2026. The listings are a mix of new equipment from suppliers and used machines from dealers and end users.
| Category | Listings on 19 November 2026 | What was listed that day |
|---|---|---|
| Industrial pumps | about 635 | Centrifugal, multistage and diaphragm pumps, many of them new and priced |
| Industrial filters | about 580 | Mostly liquid filter bags and cartridges |
| Processing vessels | about 465 | Expansion vessels and tanks, mixing and holding vessels, and laboratory reactors |
| Industrial mixers | about 150 | Ribbon, ploughshare, planetary and high shear mixers |
| Stirring vessels | about 25 | Mixing tanks and process vessels |
| Heat exchangers | 10 to 18 | Plate heat exchangers |
| Centrifuges | 10 to 18 | Laboratory centrifuges |
| Reactors | 5 | Glass-lined and stainless steel reactors |
These counts come from The Commercial Trader’s listing pages, which show nine listings a page, and they change daily. Equipment listed on 19 November 2026 included Pfaudler glass-lined reactors, a 70,524 litre stainless steel reactor, a 12,800 litre stainless steel heating vessel, a KEK ribbon mixer and Silverson mixer homogenisers, all price on application.
New pumps from Calpeda, Wilo, Ebara and Grundfos were listed that day with prices from about £540 to about £7,260. Sellers were in the UK and overseas, so use the Condition filter to show used equipment only, and check each listing’s location before you enquire.
What do you need to know before you look for a used pump?
Know the duty before you look at a single pump. A pump is chosen for a duty: the liquid it moves, the flow rate, and the pressure it has to deliver.
Take those three figures to the seller, along with the liquid’s temperature and whether it carries solids. A pump that’s too big for the duty wastes energy, and one that’s too small won’t do the job.
On a used pump, ask for the details on the nameplate, the type of seal, and the materials in contact with the liquid. Ask whether the pump has been run or tested since it was taken out of service.
What do you need to know before you look for a used mixer?
Know your batch size and what you’re mixing before you look for a used mixer. The batch size sets the working volume, and how thick the product is decides the type of mixer and the power it needs.
- How much do you mix in one batch?
- Is the product a liquid, a paste or a powder, and does it contain solids?
- Does the batch need heating, cooling or a vacuum?
- What did the mixer last handle, and how was it cleaned?
The Commercial Trader lists mixers under industrial mixers, and vessels with their own agitators under stirring vessels.
What should a used vessel or reactor come with?
A used vessel or reactor should come with its data plate, its drawings and its latest examination report. The data plate shows the capacity, the design pressure and temperature, the year of manufacture and the serial number.
Ask what the vessel is made of, including any lining, and what it held before. On a glass-lined reactor, ask when the lining was last inspected and what the inspection found.
The Commercial Trader lists these under processing vessels and reactors. The five reactors listed on 19 November 2026 were a mix of used and unused, and all were price on application.
What rules apply to second-hand process equipment?
The seller has to supply it safe, the buyer has to keep it safe in use, and pressure equipment has to be examined before it’s used. The Health and Safety Executive says anyone supplying second-hand equipment for use at work must make sure, so far as reasonably practicable, that it’s safe, and must supply adequate information with it.
The buyer’s duties come from the Provision and Use of Work Equipment Regulations, which put duties on whoever owns, operates or controls work equipment, as HSE’s guide to buying second-hand machinery explains.
Pressure equipment has an extra step. Under the Pressure Systems Safety Regulations 2000, a written scheme of examination has to be in place, and the examination carried out, before a pressure system is used, whether it’s new or second-hand. The regulations apply to systems that hold a relevant fluid at more than 0.5 bar.
What does it cost to move and install used process equipment?
The purchase price is only part of the cost of used process equipment. Disconnecting, dismantling, lifting, transport, installation and commissioning all come on top, and on a large vessel they can match the price of the equipment.
Ask the seller which of those are included before you agree a price, and get the answer in writing. The Commercial Trader’s guide to budgeting for buying and installing used process machinery goes through each cost.
How do you buy process equipment on The Commercial Trader?
Pick a process category on The Commercial Trader, filter it, and send an enquiry from the listing. The enquiry goes to the seller, and the sale is agreed between the two of you.
- Open industrial pumps for sale, or one of the other process categories.
- Set the Condition filter to used if you don’t want new equipment.
- Check each listing’s location, or add your own location and a distance.
- Send the seller your duty or specification, and ask for a price, the nameplate details and the serial number.
- Inspect the equipment, or have someone competent inspect it, before you pay.
The rest of The Commercial Trader’s industrial machinery for sale covers packaging machines, conveyors and complete lines. If you’re clearing equipment to make room, see the guide to how to value and sell used industrial machinery.
Frequently asked questions
Where is the best place to buy used process equipment in the UK?
The best place to buy used process equipment depends on how much support you need. A specialist process plant dealer gives you inspected equipment and advice on whether it suits your duty, and an auction usually gives the lowest price with the least support. A marketplace such as The Commercial Trader lets you compare equipment from many sellers before you contact anyone.
Can you buy used process equipment on The Commercial Trader?
Yes. The Commercial Trader had about 635 pump listings, about 465 processing vessels and about 150 mixers on 19 November 2026, new and used, plus five reactors. Set the Condition filter to used to leave out new equipment.
Does a used pressure vessel need examining before it’s used?
Yes, if it’s part of a pressure system covered by the Pressure Systems Safety Regulations 2000. A written scheme of examination has to be in place, and the examination carried out, before the system is used, whether the vessel is new or second-hand. The regulations cover systems holding a relevant fluid above 0.5 bar.
Can a used vessel or reactor be put to work on a different product?
Only if its materials and its ratings suit the new product. Check the material of construction, the design pressure and temperature on the data plate, and what the vessel held before. Ask the maker or a competent engineer before you commit, because there’s no safe rule of thumb.
Does used process equipment come with a warranty?
Sometimes. A dealer or a manufacturer may give a warranty on used or reconditioned process equipment, and an auction or a private sale usually doesn’t. Get any warranty in writing, with what it covers and for how long.
Does used process equipment have to be safe when it’s sold?
Yes. Anyone supplying second-hand equipment for use at work must make sure, so far as reasonably practicable, that it’s safe, and that includes dealers, auctioneers and private sellers. The buyer then has to keep the equipment safe in use.
Who pays to dismantle and transport used process equipment?
The buyer usually pays, unless the seller has agreed otherwise in writing. Ask who will disconnect, dismantle, lift and deliver the equipment before you agree a price, because on a large vessel those costs can match the purchase price.